DSP-Board D.Module2.C6747

Das D.Module2.C6747 basiert auf dem Texas Instruments TMS320C6747 Prozessor. Es zeichnet sich durch geringen Stromverbrauch und eine Vielzahl von Schnittstellen für die Sensoranbindung und Kommunikation aus.

Key Features

TMS320C6747 Floating Point DSP
100MBit Ethernet, USB2.0
64 Mbytes RAM
vielfältige Peripherie-Schnittstellen
2xUART, I2C, SPI, GPIO
niedriger Energiebedarf
eigenständiger Betrieb ohne PC

Anwendungen

Das D.Module2.C6747 eignet sich hervorragend für die industrielle Messtechnik, Sensorik und Regelung. Die große Anzahl serieller McASP- Kanäle z.B. erlaubt den Aufbau vielkanaliger hochauflösender Datenerfassungs-Systeme mit synchroner Abtastung, wie sie unter anderem in der Schwingungsmesstechnik benötigt werden. Für die Anbindung an einen Host-Rechner stehen USB und Ethernet zur Verfügung.

Spezifikationen

DSP	TMS320C6747	300, 375, or 456 MHz floating-point DSP, 2400, 3000, or 3648 MMACS
Memory	DSP-internal	32K bytes data cache, 32K bytes program cache, 256K bytes direct mapped or level-2 cache, 128K bytes shared RAM
	SDRAM	64M bytes, 133 MHz operation, 32-bit wide, 512M bytes/s peak throughput
	Flash	8M bytes NOR with SPI interface, sector architecture, optional NAND Flash, SD/Multi-Media-Card Interface
Ethernet	100Base-Tx, 10Base-T	onboard PHY and magnetics with integrated 2-port switch, 100Base-Fx Fiber support with external transceiver
USB	2	USB2.0 OTG (480 Mbit/s) and USB1.1 Host (12 MBit/s)
UART	2	transmit and receive Fifo, DMA support, Port 1: RS232: max 460,8K baud, automatic hardware flow-control, Port 2: RS422/485: max. 3M baud
SPI	1	max. 50 Mbps, master and slave mode
I2C	1	max. 400 kbps, 7 and 10 bit addressing modes, master and slave mode
McASP	2	independent receivers and transmitters, max. 50 Mbps throughput
Timer	3	2 x 32/64-bit, 1 x 16-bit high speed timer with 10ns resolution
GPIO	16	bit-wise programmable, input or output
External Bus Interface	EMIF	asynchronous transfers, 16/32-bit data bus, 14 address lines, 2 pre-decoded chip selects, configurable timing
Real-Time Clock	1	provision for external buffer power supply
Quadrature Decoder	2	quadrature and direction/count mode, Index and Strobe inputs, 32 bit counter registers
PWM	3	16-Bit Time-Base Counter, 6 Single Edge, 6 Dual Edge Symmetric or 3 Dual Edge Asymmetric Outputs, Dead-Band, PWM Chopping, Trip Zone
Capture Timer	3	up to 4 events per channel, also configurable as auxillary PWM
System Supervisor		voltage and watchdog
Emulation Interface		JTAG
I/O Level	LVTTL / LVCMOS	all signals except ETH and USB: high level min. 2V, max. 3.5V, low level min. -0.2V, max. 0.8V, output drive: external bus interface:± 12 mA, all others ± 4 mA
Power Supply	3.3V	single supply, 750mA typ.
Firmware	D.Module2.BIOS	bootloader, board initialization, board configuration, flash memory programming, UART and USB I/O
	Setup Utility	program and data file uploads to the flash memory via USB or UART
	Config File	user- configurable text file with program and initialization parameters
Temperature Range		0 – 70°C
Connectors	BUS1, BUS2, COM, EXP	Molex 71436-2164
	JTAG	14-pin, 2.54mm pitch
Mechanics		86.8 x 58.4 mm, overall height: 16mm
ROHS		compliant

Note: pin multiplexing on the TMS320C6747 DSP imposes some restrictions on the simultaneous use of peripherals. Please refer to the D.Module2.C6747 data sheet for detailled information.

Bestellangaben

D.Module2.C6747	standard module
DK.C6747	C6747 development kit including D.Module2.C6747, XDS100 JTAG in-circuit emulator, D2.Base.P base board, power supply, RS232 and USB cable, support software, user's guide, and free support via Email or phone
DK.C6747-FMC	C6747 and FPGA development kit including D.Module2.C6747, D.Module2.6SLX45T, XDS100 JTAG in-circuit emulator, D2.Base-FMC base board, power supply, USB cable, DSP support software, FPGA interface examples in VHDL, user's guides, and free support via Email or phone
DS.TCP/IP-C6747	Ethernet software development kit including libraries, sample programs, documentation, and evaluation license for the D.SignT TCP/IP stack

Kompatibilität

Das D.Module2.C6747 kann aufgrund der Vielzahl von Schnittstellen und Konfigurationen als Alternativprodukt zu anderen Mitgliedern aus der Texas Instruments C674x Familie eingesetzt werden. Die folgende Seite vergleicht das D.Module2.C6747 mit anderen Prozessoren aus dieser Familie.

C674x_Low_Power_DSP

Peripherie-Boards

Entwicklungswerkzeuge

Emulatoren

Compiler

Code Composer Studio

Prototyping Boards

Anfrage starten Datenblatt Dokumentation und Software Wiki